Port LOGGING - DLT-VERBOSE

Access to DLT verbose messages

Stimulation

此端口不具备激励能力。

Name

在以下情况下可用

默认值

有效值

Type

Description

Active mode

☑

bool

Whether the port is also allowed to send network packets. If unset, the port can only passively receive packets.

物理层 ❲网络访问❳

Port

string

Name of the port inside a network. In Vector Hardware Config, the network-based mode must be activated.

MAC 地址 ❲客户端❳

Active mode is enabled

‘02:00:4C:4F:4F:50’

string

字符串(格式:02:00:4C:4F:4F:50),如果要使用默认 MAC 地址,则为 ‘default’

Logger Protocol Settings

Active mode is disabled

Logger protocol

Active mode is disabled

[, ASAM CMP, PLP/TECMP]

string

Use a logger protocol such as ASAM CMP. Ethernet frames contained in the logger messages are then extracted.

Device and Stream IDs

Active mode is disabled » Logger protocol: ‘ASAM CMP’

string

Identifiers of the devices and streams as a list of tuples, each consisting of device ID and stream ID, e.g.: (1,2),(3,4). Leave empty if no filtering based on device and stream ID is needed.

Interface IDs

Active mode is disabled » Logger protocol: ‘ASAM CMP’

string

Identifiers of the interfaces: empty if no filtering based on interface IDs is required; several can be separated by commas.

Device IDs / Probe IDs

Active mode is disabled » Logger protocol: ‘PLP/TECMP’

string

Identifiers of the devices / probes: empty if no filtering based on device / probe IDs is required; several can be separated by commas.

Interface IDs / Bus Spec IDs

Active mode is disabled » Logger protocol: ‘PLP/TECMP’

string

Identifiers of the interfaces / bus specs: empty if no filtering based on interface / bus spec IDs is required; several can be separated by commas.

Outer VLAN mode

Active mode is disabled

disable

[disable, single tagging, single tagging (any ID)]

string

If set to ‘single tagging’, take an additional IEEE 802.1Q tag outside the logger protocol into account and filter by the specified VLAN id; or if set to ‘single tagging (any ID)’, the tag itself must be present but the VLAN id is not relevant.

Outer VLAN id

Active mode is disabled » Outer VLAN mode: ‘single tagging’

0

int

Filter incoming packets by this VLAN id, so only packets with a matching VLAN id will pass.

VLAN Settings ❲IEEE 802.1Q❳

VLAN mode

disable

[disable, single tagging]

string

如果应使用数据库中的 VLAN ID,则设为 ‘auto’;如果不应使用 VLAN,则设为 ‘disable’;如果应指定固定的 VLAN ID,则设为 ‘single tagging’

VLAN id

VLAN 模式:‘single tagging’

0

int

如果传入的数据包带有 VLAN 标签,则会对其进行过滤,只有带有该 VLAN ID 的数据包才能通过。不带任何 VLAN 标签的传入数据包也会通过过滤器。

IP Settings

Active mode is enabled

IP version

Active mode is enabled

IPv4

[IPv4, IPv6]

string

所用 IP 版本的选择

IP 地址 ❲客户端❳

Active mode is enabled

string

用作客户端的 IP 地址。它必须与被测设备的 IP 地址位于同一子网,且不得等于其他参与者的 IP 地址,也不得等于操作系统分配给所选网络接口的 IP 地址。

Subnet mask / prefix length

Active mode is enabled

‘default’

string

对于 IPv4 地址,可以给出子网掩码或前缀长度(格式:‘255.255.255.0’ 或 ‘24’)。‘default’ 使用该 IP 地址(客户端)所属网络类的默认子网掩码。

对于 IPv6,只接受前缀长度,且不支持值 ‘default’。

网关地址

Active mode is enabled

string

网关的 IP 地址,通过该网关可以访问本地子网之外的主机。如果不需要网关,请留空

DLT Settings

Active mode is enabled

DLT TCP auto reconnect timeout [sec]

Active mode is enabled

float

ecu.test will automatically restart the DLT TCP connection if no new DLT messages arrive within the configured number of seconds. An empty value for the timeout switches the auto reconnect feature off.

Pre-recording circular buffer

Active mode is enabled

0

int

Since the recording gets started only a short time after the connection to the ecu is established, even with auto-start/stop, messages sent by the ECU only once immediately after the connection is made, can be lost. With this setting, the recording can be “extended forward” by the specified number of messages, in order to include these initial messages.

Reconnect

In Active Mode, reconnects and clears the message buffers.

Parameterization

返回值

Name

在以下情况下可用

默认值

有效值

Type

Description

result

False

[False, True]

bool

Returns True if the connection was successfully established